Most rigid box problems are size problems. The product rattles, the lid will not close, the insert sits too high, or the box arrives a few millimetres off and the whole run has to be redone. All of these are avoidable if you settle three things before you brief a manufacturer: which dimensions you are quoting, how much clearance the product needs, and how much space the board itself takes up.
This guide walks through each one, with a worked example you can follow with your own product.
Inner size vs outer size: decide which one you are quoting
Every rigid box has two sets of dimensions.
- Inner (internal) size is the space available for the product. It is what your product has to fit inside.
- Outer (external) size is the finished size of the box as it sits on a shelf or in a shipper. It is the inner size plus the thickness of the board on every side.
Mixing these up is the most common sizing mistake. If you tell a supplier "120 x 80 x 30 mm" and they read it as the outer size while you meant the inner size, your product will not fit. Always write "inner" or "outer" next to every dimension in your brief.
As a rule, size the box from the product outwards: measure the product, add clearance, add board thickness, and arrive at the outer size.
Step 1: Measure the product at its widest points
Measure length, width and height at the largest point of the product, including caps, pumps, ribbons, tags or anything that sticks out. Measure the product in the position it will sit in the box. For anything with an irregular shape, such as a bottle with a shoulder, measure the bounding box: the smallest rectangle that contains the whole product.
If the product ships with an insert, a leaflet or tissue, measure it with all of those in place.
Step 2: Add clearance
Clearance is the small gap between the product and the box wall. Too little and the product will not go in smoothly, or the lid will bind. Too much and the product moves around in transit.
A common starting point is 2 to 3 mm per side for a snug fit, and a little more where the product has to slide out easily. Add a few millimetres of headroom in height so the lid is not pressing on the product. Your manufacturer can adjust these numbers to the construction you choose, so treat them as a starting point rather than a rule.
Step 3: Add the board thickness
Rigid boxes are made from thick greyboard, commonly between 1.5 and 3 mm. The walls take up real space, so the outer size is larger than the inner size by the board thickness on each side.
For a typical setup box (separate lid and base), the outer length and width are roughly the inner size plus two board thicknesses. A 2 mm board adds about 4 mm to each outer dimension. The height depends on the structure, because the lid, base and any shoulder or neck all add to it.
A worked example
Say you are packing a product that measures 120 x 80 x 30 mm, and you want a setup box with 2 mm board.
| Step | Length | Width | Height |
|---|---|---|---|
| Product | 120 | 80 | 30 |
| Add clearance (2 mm per side, 3 mm headroom) | 124 | 84 | 33 |
| Inner size | 124 | 84 | 33 |
| Add board (2 mm each side) | 128 | 88 | about 37 |
| Approximate outer size | 128 | 88 | about 37 |
These are working numbers. The exact outer height depends on the lid depth and the structure, which is why it helps to see it before you commit.
How the box style changes the numbers
- Setup box (lid and base): the lid sits over the base with a small allowance, so the lid is slightly larger than the base. The lid depth is a design choice and changes the look of the box.
- Drawer box: a tray slides inside a sleeve. You need extra room so the tray moves freely without rattling.
- Magnetic flap box: a hinged cover closes over the base. The flap depth and the hinge take extra space compared with a plain lid.
- Book-style box: the lid is hinged along one edge and opens like a book. Leave room for the hinge.
- Shoulder-neck box: the lid sits on a raised neck, so total height is higher than a plain setup box for the same product.
Inserts, ribbon pulls and trays also take up room. If your design has any of them, tell your manufacturer so they can size around them.
Common sizing mistakes to avoid
- Copying someone else's outer size. A size that works for another product with another board thickness will not necessarily work for yours.
- Forgetting the board thickness. The product fits the inner size, not the outer size.
- Measuring the product without its accessories. Caps, pumps and tags all add millimetres.
- Skipping the sample. Measurements on paper are never a substitute for holding the box. Approve a physical sample before production.
- Changing the size after the artwork is done. Artwork is laid out to a specific dieline. A size change means the layout has to be redone.
See it before you order
If you can see the box before you commit, most of these mistakes disappear. Our rigid box dieline tool lets you enter your outer size and see a setup, drawer, magnetic, book-style or shoulder-neck box in 3D. Slide it open and shut, change the colour and surface finish, and check the proportions against your product. The preview is free. When you are ready for production, you can unlock the board dieline for your exact size and get a firm quote from our team.
If your structure is not one of the standard styles, choose "Other structure" in the tool and our engineers will model it. We manufacture rigid boxes of every kind.
Frequently asked questions
Should I give my manufacturer the inner or outer size?
Either works, as long as you label it clearly. Many brands give the product size and let the manufacturer work out the box, which removes the risk of getting the arithmetic wrong.
How much clearance should I leave around my product?
A common starting point is 2 to 3 mm per side for a snug fit, plus a few millimetres of headroom. The right number depends on the product, the insert and the construction, so confirm it against a physical sample.
How thick is the board in a rigid box?
Commonly between 1.5 and 3 mm. Thicker board gives a sturdier, more premium feel but makes the outer size larger for the same inner size.
Does the finish change the size?
Matte, soft-touch or gloss finishes do not change the size in any way you would notice. The board thickness and the structure matter far more.
Can I check the size before ordering?
Yes. Use the free 3D preview in our dieline tool to check proportions, and always approve a physical sample before production.
Universal Offsets manufactures rigid boxes at our Noida facility, with printing, finishing and box-making under one roof.